Automotive Plastic Housings: Design, Process and the Mistakes That Reach PPAP
An ECU box, a sensor shell, a lamp housing, a connector body. Simple shapes, hostile environment, and a validation file that punishes every shortcut. Here is what decides whether the part passes.
What "housing" covers on a vehicle
The word hides a wide range of parts with very different requirements.
|
Part |
Typical material |
What actually decides the design |
|
ECU / control unit enclosure |
PA66-GF30, PBT-GF30 |
Heat, sealing, EMC, connector position |
|
Sensor housing (cam, radar, ultrasonic) |
PBT-GF30, PA66-GF30 |
Optical or radar window, dimensional stability |
|
Lamp housing and bezel |
PC, PC/ABS, PMMA |
UV, clarity, thermal cycling with the bulb |
|
Connector body |
PBT-GF30, PA66 |
Pin position, latch strength, creep |
|
Motor end cap, actuator cover |
PA66-GF30, PPS |
Heat, vibration, bearing seat |
|
Battery pack cover, module frame |
PP-TD20, PA6-GF |
Flame retardancy, mass, stiffness |
|
Door lock, latch, interior mechanism |
POM, PA66 |
Wear, noise, lubricant-free running |
|
Interior trim housing |
PC/ABS, ABS |
Appearance, scratch, UV, cost |
Two parts on that list can share a material and share nothing else. The requirement that dominates is almost always one of four: heat, sealing, dimensional stability, or appearance.

Four constraints that are not negotiable
1. Temperature cycling. Under-bonnet parts see −40 °C to +125 °C, with the engine heat soaking in after shutdown. Interior electronics see −40 to +85 °C. The damage is not the peak temperature - it is the differential expansion between the plastic, the metal insert, the PCB and the potting compound, repeated a thousand times.
2. Chemistry. Fuel, oil, coolant, brake fluid, washer solvent, road salt, and whatever the owner sprays on the engine. A material that passes a single immersion test can still fail after a season of splashing and evaporation.
3. Vibration. Engine and transmission mounts see continuous excitation; a housing that resonates will fatigue its own mounting bosses and crack the PCB inside.
4. Documentation. Automotive is the one industry where the paper is part of the product: PPAP, dimensional results, material certificates, IMDS entries, flammability (UL94, FMVSS 302) and ELV compliance. A perfect part with an incomplete file is a rejected part.

Process choice: three phases, three answers
|
Phase |
Quantity |
Process |
What it is good for |
|
A-sample, fit and function |
1–20 |
CNC machining, 3D printing |
Fast geometry, real material, no tooling |
|
B-sample, validation build |
20–300 |
Vacuum casting, CNC, or bridge tool |
Enough parts for test houses and vehicle builds |
|
C-sample, production |
1,000+ |
Injection moulding |
Unit cost, repeatability, material certification |
The most expensive mistake in this table is using an A-sample to prove a C-sample requirement.
A machined housing is cut from extruded or compression-moulded stock. It has no gate, no weld line, no fibre orientation from flow, and no moulded-in stress from packing. A moulded housing has all four. So a machined prototype can pass a dimensional check and an IP test, and the moulded part can still warp out of the sealing groove - because the two parts are not the same part, even when the drawing is identical.
Use prototypes to prove architecture: does the connector fit, does the PCB clear, does the harness route, does it assemble in the fixture. Do not use them to prove warpage, weld-line strength or moulded-in stress.

Six design traps in housing work
1. Wall thickness transitions. A sudden step from 2.5 mm to 4 mm produces a sink mark on the cosmetic face and a void inside. Ramp the change over at least 3:1, or split the part.
2. Bosses. A solid boss is a heat reservoir: it shrinks more than the wall around it and pulls a depression on the opposite face. Boss wall should be about 60% of the nominal wall, with a radius at the base and gussets if it takes load.
3. Ribs. Same rule - rib thickness around 50–60% of wall. Ribs that match the wall thickness guarantee sink marks on the visible side.
4. Sharp internal corners. A stress riser in a part that vibrates for a decade. Radius everything; the tool will thank you as well.
5. Draft. One to two degrees on every vertical face. Textured surfaces need more: roughly one extra degree per 0.025 mm of texture depth, or the part scuffs on ejection.
6. The sealing groove. This is where housings actually fail. Groove width and depth must match the O-ring or gasket cord, with a compression of roughly 15–25% for a static seal, and the groove floor must be flat and free of weld lines. A gate placed near the groove puts a weak, porous weld line exactly where the seal sits.

Sealing and EMC: the two requirements that fight the design
Sealing wants a smooth, flat, continuous groove, generous wall stiffness so the housing does not breathe under pressure change, and a gasket that is compressed evenly - which means fasteners spaced closely enough around the perimeter.
EMC wants a conductive path from the housing to the chassis, which usually means conductive coating, a stamped shield, or a filled compound. Every one of those adds a process step and a failure mode, and the coating has to survive the same thermal cycling as the plastic.
Practical answers that work:
Machine the sealing groove on prototype and low-volume parts; mould it in production, with the gate placed away from the groove.
Keep the groove on one half only. Splitting the seal between two moulded faces doubles the tolerance stack.
Put the shield on a separate carrier rather than coating the whole housing, so a coating defect does not scrap the part.
Test as assembled, at temperature, not at 23 °C on a bench.

Materials, and the trade each one makes
|
Material |
Strength |
Weakness |
Use |
|
ABS |
Cheap, easy, good surface |
Poor heat and chemical resistance |
Interior, low-load covers |
|
PC/ABS |
Tough, good surface, moderate heat |
Not for fuel or long UV |
Interior housings, bezels |
|
PA66-GF30 |
Stiff, heat resistant, strong |
Warps badly, absorbs moisture |
Under-bonnet structural housings |
|
PBT-GF30 |
Dimensionally stable, good electricals |
Notch-sensitive, warps with flow |
Connectors, sensor bodies, ECU |
|
PP-TD20 |
Cheap, chemical resistant, light |
Low stiffness, poor UV without stabiliser |
Battery covers, large trims |
|
POM |
Wear, low friction, dimensional |
Poor adhesion, hard to bond |
Latches, gears, mechanisms |
The pattern worth remembering: amorphous plastics (ABS, PC/ABS) are easy to mould and pleasant to look at; semi-crystalline glass-filled plastics (PA66-GF, PBT-GF) hold their properties hot but warp because the fibres orient with the flow. Choosing between them is choosing which problem you would rather solve.
Tolerance and warpage: the honest numbers
Moulded part tolerances follow ISO 20457 (which replaced DIN 16742), and they are not the same as machining tolerances. A 100 mm moulded dimension in a glass-filled material is typically good to a few tenths of a millimetre, and the tolerance band widens with size and with the number of moulded features stacked in the same direction.
Warpage is the dominant error in large housings, and it is a process problem, not a drawing problem:
Fibre orientation follows the flow, so a glass-filled part shrinks differently along and across the flow.
Cooling differences between the cavity and core sides bend the part.
Uneven wall thickness creates uneven shrinkage.
Packing pressure and gate location decide how much of that you get.
The design responses: keep walls uniform, use flow simulation before cutting steel, place the gate where the weld line does no harm, and specify flatness on the faces that seal rather than on the whole part.
Do not put a machining tolerance on a moulded housing. It will be read as a rejection criterion and it will reject good parts.
Validation and the file
For an automotive housing, the deliverable is a package:
Dimensional report on the drawing's datums, with CMM results and a clear statement of the measurement temperature.
Material certificate with lot traceability, and the IMDS entry.
Flammability results to the applicable standard.
Sealing test at temperature and pressure, with the leak rate stated.
Thermal cycling and vibration results, or the test house report.
PPAP at the level the customer requires, with the process flow, control plan and MSA behind it.
First article from the production tool, not from a bridge tool.
That last point is the one that catches programmes late. A bridge tool produces parts that pass; the production tool, with a different gate position and cooling layout, produces parts that do not - and by then the vehicle build is two weeks away.
What to send with an enquiry
1. The drawing with datums, and the tolerance standard you are working to.
2. The environment - temperature range, fluids, UV, wash, vibration source.
3. The sealing and EMC requirements, and whether they are tested assembled.
4. The mating parts - connector, PCB, harness, bracket - because housings fail at interfaces.
5. Volume and phase - A, B or C sample - and the programme timing.
6. The documentation set you will require at each phase.
A housing enquiry that arrives with the environment and the documentation list gets a useful answer. One that arrives with a STEP file and the word "urgent" gets a price and a hope.
About the manufacturer
Shenzhen Strongd Model Technology Co., Ltd. produces moulded, machined and cast plastic parts and metal components for automotive, robotics, medical and consumer electronics customers. The 40,000 m² plant in Shenzhen runs 85 CNC machining centres, 18 of them five-axis, with injection moulding and vacuum casting for bridge volumes, and Hexagon CMM inspection. The quality system is certified to IATF 16949:2016 and ISO 9001:2015; prototypes ship in 3–7 days and quotations are returned within 8 working hours.
Website: https://www.strongdcnc.com/
