Which Parts Are Actually Made From PEEK

Nov 16, 2026

Leave a message

Which Parts Are Actually Made From PEEK

A part-by-part map of where PEEK earns its price - semiconductor, medical, aerospace, oil and gas, automotive, food - plus the shapes that are hard to machine and the ones that should never be PEEK at all.

 

The one-line rule

PEEK is rarely chosen because it is "the best plastic". It is chosen because a metal part was failing, or because a cheaper plastic ran out of temperature, chemical resistance or cleanliness.

That single sentence explains almost every PEEK part in existence: they are small, highly loaded, and exposed to something aggressive - heat, chemicals, sterilisation, high vacuum, or the human body. You almost never see PEEK as a large housing or a cosmetic cover, because at that size the cost stops making sense.

img-mwimqm7z-6509a9a4

The map, in one table

Industry

Typical PEEK parts

Why PEEK, in one phrase

Semiconductor

Wafer handling forks, CMP retaining rings, chamber insulators, chemical valve bodies

Low outgassing, no metal contamination, survives wet chemistry

Medical

Instrument handles, trocar and endoscope parts, spinal cages, dental abutments, sterilisation trays

Repeated autoclave, radiolucent, modulus close to bone

Aerospace

Fuel-system bushings, pump wear rings, cable clamps, brackets near hot zones

Jet fuel resistance, 200 °C+, low smoke, weight saving

Oil and gas

Back-up rings, seal carriers, connector bodies, insulator sleeves

Resists extrusion at high pressure and temperature, H₂S and CO₂

Automotive and industrial

Thrust washers, pump wear plates, compressor valve plates, gear pads

Runs without lubrication, survives heat and cycling

Food and beverage

Pump and valve parts, filler nozzles, wear rings

Withstands steam cleaning, food-contact grades available

Six industries, one common thread: the part is small, the environment is hostile, and failure is expensive.

img-mwimxbp2-13705e76

Semiconductor: the largest single user

A chip fab is where PEEK is most at home, because the requirements there are unusual: no particles, no outgassing, no metal ions, and resistance to aggressive wet chemistry.

Wafer handling forks and paddles. They pick up a wafer by its edge, so flatness and stiffness matter at a thickness of a few millimetres. Carbon-filled PEEK is common because it adds stiffness and can be made static-dissipative.

CMP retaining rings. They hold the wafer edge during chemical-mechanical polishing, running against a slurry at controlled pH. The ring wears, so it must wear evenly and not shed particles into the process.

Chamber insulators and feedthrough bodies. They sit in vacuum and see plasma. Outgassing and thermal stability decide the material.

Wet-process valve bodies, nozzle plates and fittings. High-purity chemical delivery, where a corroded stainless part would contaminate the line.

The specification here is rarely "PEEK" alone. It is a grade, a cleanliness level, and a cleaning procedure.

img-mwimvbf2-b09da81a

Medical: three very different jobs

Medical buyers use the same word for three unrelated problems.

Reusable instruments. Handles, forceps bodies, trocar components and endoscope housings go through steam autoclave cycles at around 134 °C, hundreds of times. Most engineering plastics go cloudy, craze and crack. PEEK keeps its dimensions, which is why it appears on instrument trays and insulated shafts.

Implants. Spinal fusion cages and dental components are the classic case, and the reason is not strength - titanium is stronger. It is two other things:

Radiolucency. PEEK is invisible on X-ray and produces no MRI artefact, so the surgeon can see bone healing through the implant instead of a bright white block.

Modulus. PEEK sits at roughly 4 GPa against cortical bone around 15 GPa and titanium around 110 GPa. Closer to bone means less stress shielding, so the adjacent bone keeps its density.

Sterilisation hardware. Trays, brackets, and holders that must survive the autoclave without warping, and must not scratch the instruments they carry.

Implantable parts are a different business from machined industrial parts: they need implantable-grade resin, full traceability, and a quality system certified for medical devices. Anyone quoting an implant component without asking about those three things is not a serious supplier for it.

img-mwin494a-bb6b73e2

Aerospace: fuel, heat and weight

Three separate applications, three separate reasons.

Fuel system parts - bushings, wear rings, pump components. PEEK swells very little in jet fuel and does not need external lubrication in many sliding contacts.

Hot-zone hardware - clamps, brackets, cable guides near engines and bleed air. The 250 °C continuous rating is the entry ticket.

Interior and airframe - parts where flame, smoke and toxicity rules apply. PEEK burns with low smoke and has a high limiting oxygen index, so it passes tests that rule out cheaper plastics.

The recurring theme is replacement: a metal bracket that frets, corrodes or needs a lubricant becomes a PEEK part that does none of those things.

img-mwin6652-dcd38cb4

Oil and gas: the pressure problem

Downhole tools combine 150–200 °C, high pressure, H₂S, CO₂ and mechanical load. PTFE seals are chemically excellent but extrude under pressure, so PEEK appears as the hard part behind the soft seal.

Back-up rings - sit behind an O-ring or a PTFE seal and stop it extruding into the gap. PEEK's combination of strength at temperature and chemical resistance is exactly what this part needs.

Seal carriers and gland bodies.

Electrical connector bodies and insulator sleeves for downhole logging tools, where the part is both structural and insulating.

Valve seats and choke components in aggressive flow.

img-mwimsn1e-a7471863

Automotive and industrial: the unlubricated part

The automotive use of PEEK is mostly about removing maintenance, not saving weight.

Thrust washers and gear pads in transmissions and pumps, running in oil at 120–150 °C.

Pump wear plates and bushings, where the part runs against a metal face with only the process fluid for lubrication.

Compressor valve plates, a thin, fatigue-loaded flapper that used to be steel. Carbon-filled PEEK tolerates the impact cycling and does not corrode.

Wear strips and guides on conveyors and packaging machinery, where a metal slide would need grease.

The value here is measured in service intervals, not in material cost.

Food and beverage: cleaning is the requirement

Filler nozzles, pump parts, valve seats and wear rings in filling and packaging lines face daily caustic and acid cleaning cycles at temperature, followed by steam or hot-water sanitising.

PEEK holds its dimensions through that routine, does not absorb taste or odour, and is available in food-contact grades. The parts are usually small and replaced on a schedule, which makes the material cost acceptable.

Shapes that are hard to machine

Knowing which parts are PEEK is one thing; making them is another. Six shapes cause most of the trouble, and each has a known answer.

Part shape

The problem

What works

Thin ring (retaining ring, back-up ring)

Clamping turns a circle into a triangle

Soft jaws or a split sleeve; rough and finish in separate operations; measure roundness free-standing

Long thin plate (wafer fork, wear strip)

Deflects under cutting force and chatters

Support underneath, light radial depth of cut, remove material symmetrically from both sides

Deep thin-wall housing (connector body, valve body)

Chips pack in, heat has nowhere to go

High-pressure air blast, small radial engagement, sharp tool changed before it dulls

Sealing face or valve seat

Smearing instead of cutting; flatness lost

Fresh edge for the finishing pass, no dwelling, check flatness on a plate not in software

Fine or deep bore (nozzle, insulator sleeve)

Bore closes in from elastic recovery

Drill undersize, then ream or bore; allow for recovery in the finishing allowance

Thin flat washer (thrust washer)

Burr and parallelism

Machine both faces, vacuum chuck for finishing, deburr by controlled method not by hand

The common thread: PEEK punishes clamping force and dull tools far more than aluminium does. A fixture that works for aluminium will often distort a PEEK part.

Parts that should not be PEEK

Saying no is part of specifying well. Do not choose PEEK for:

Large covers, housings and panels. The material cost dominates and the properties are wasted.

High-impact or drop-loaded parts. PEEK is notch-sensitive; a tougher, cheaper plastic does better.

Outdoor parts with sustained UV exposure. The surface embrittles.

Continuous hot steam or hot water near the service limit. Hydrolysis takes its toll.

Strong oxidising acids such as concentrated nitric or sulphuric.

Simple wear parts in high volume. POM or PA moulded at volume will be a fraction of the price.

Anything where the only requirement is "chemical resistance". PP or PVDF may be enough.

What to put on the drawing

For a PEEK part, five items carry more weight than the tolerance block:

1. The part's function - what it seals, guides, insulates or carries.

2. The grade - unfilled, CF30, GF30, bearing grade, medical, semiconductor.

3. The environment - medium, temperature, pressure, cleaning or sterilisation cycle.

4. The inspection condition - temperature and rest time, because PEEK moves with both.

5. The cleanliness requirement - especially for vacuum, semiconductor and medical parts, where handling matters as much as machining.

Add the 3D model, the 2D drawing, the mating parts and the acceptance rules, and the quote can be built on facts rather than assumptions.

 

About the manufacturer

Shenzhen Strongd Model Technology Co., Ltd. machines engineering plastics - PEEK, PPS, PSU and PTFE - alongside aluminium, stainless steel and titanium, for robotics, automotive, medical and consumer electronics customers. The Shenzhen plant covers 40,000 m² and runs 85 CNC machining centres, 18 of them five-axis, with Hexagon CMM inspection under ISO 9001:2015 and IATF 16949:2016. Prototypes ship in 3–7 days; quotations are returned within 8 working hours.

Website: https://www.strongdcnc.com/

Send Inquiry